How to disable synchronising log in Outlook 2007?

1. 'Tools' / 'Send/Receive' / 'Send/Receive Settings' / 'Define Send/Receive Groups'. Select the group. Click on 'Edit'. Clear the tick mark before 'Download offline address book'.
2. 'Tools' / 'Options' / 'Other' / 'Advanced Options'. Clear the tick mark before 'Enable logging'.

How to extract audio from video?

Best method - Format Factory 格式工厂

Method 2 - The latest version of QQ Player has the function.

Method 3 - http://www.flv2mp3.com/

How to download Youtube videos?

The best way -
http://convert2mp3.net/en/

Install ClipGrab.

http://www.computerhope.com/issues/ch001002.htm

http://www.savevideodownload.com/download.php

Microsoft Exchange Server reported error (0x8004010f)

Cause: Outlook tries to download the offline address book which is not necessary.

Solution:
How to turn off the option to download the offline address book?
1. On the Tools menu, point to Send/Receive, point to Send/Receive Settings, and then click Define Send/Receive Groups.
2. Click Edit.
3. Click to clear the Download offline address book check box, and then click OK.
4. Click Close to close the Send/Receive Groups dialog box.

When the outside caller hangs up the call, the receiver extension is disconnected in too long time.

'DISA' / 'Settings' / 'Timers' / 'DISA Ring Time after Intercept(s)' - change it to '10'.

How to let an outside caller directly call an extension instead of Operator (101)?

1. Record an OGM message on 101.
2. 'DISA' / 'Settings' / 'Security' / 'DISA Security Mode' - change it to 'None'.
3. Done.

When there is an incoming call, the ringing time is too short

'DISA' / 'Settings' / 'DISA Ring Time before Intercept(s)' - change it to '120'.

How to cancel incoming call auto transfer to operator, when no answer?

DISA / Settings / 'DISA Intercept Mode' - change 'Intercept' into 'Disconnect'.

Advertisement Board Editing

1. After installing the driver and NeoVision software, open Device Manager, check the Port number in the Properties of 'Silicon Labs CP210x USB to UART Bridge (COM4)' in Ports.
2. In Port Settings in the Properties dialogue box, change 'Bits per second' to '115200'.
3. Open NeoVision, click on 'Config'. Change 'Serial port' to 'COM4'. Change 'Baud Rate' to '115200'. Click on 'OK'.
4. Click on 'Read' to get the data.
5. Click on the piece of message, then click on 'Edit' to edit the message.

CKEditor and CKFinder installation

http://drupal.org/node/728210

I found that lot`s of people out there finding difficulty with the installation of CKEDITOR and CKFINDER.

Nobody taught me how to install it properly but I spent time with it and read all the manuals came with CKEDITOR and CKFINDER, that`s it everything goes well.

But I know that most of the people who installed these modules has got some errors or warnings like You don`t have access to brows the file or something similar warning messages.

I hope at least after this tutorial everybody will stop complaining about CKEDITOR and CKFINDER Installation.

OK I don`t wanna waste your time by talking so much... Let`s START...

Please follow the steps below;

(1) Go to http://drupal.org/project/ckeditor and download the module.
(2) Go to http://ckeditor.com/download and download CKeditor
(3) Go to http://ckfinder.com/download and download CKfinder
(4) Extract the CKeditor file downloaded from http://drupal.org/project/ckeditor then Double click and open the ckeditor file and you can see an another folder with same name ckeditor, double click and open it and then you can see a text file named COPY_HERE.txt

if you read that file you will find that why that folder is for. In this ckeditor folder you have to put the file you downloaded from http://ckeditor.com/download link.

So extract the file you dowloaded from Ckeditor.com and double click and open the file ckeditor and copy all the files in side the ckeditor and put it in the ckeditor folder which we dowloaded from drupal site.

(5) Now the file we downloaded from Drupal should look something like this ckeditor>ckeditor>ckeditor.php...
(6) Extract the dowloded file ckfinder and put it in Ckeditor folder. Now the pathe shoul look like this ckeditor>ckfinder
(7) Open ckeditor>ckfinder>config.php and remove the

CheckAuthentication() function:
        (don't worry, this function is defined in filemanager.config.php, see below)

        function CheckAuthentication()       <- remove it
        {                                    <- remove it
           //WARNING : DO NOT simply...      <- remove it
           ...                               <- remove it
           return false;                     <- remove it
        }                                    <- remove it

(8) ckeditor>ckfinder>config.php add the path to userfiles

$baseUrl = '/public_html/yoursitename.com/sites/all/modules/ckeditor/ckfinder/userfiles/'; (you can find this path from cpanel. Open the file ckeditor>ckfinder>userfiles and you can see the path to the userfiles on top left side of cpanel.)

(8) Add this code

require_once '../../../../includes/filemanager.config.php';

straight below the following line:

$baseDir = resolveUrl($baseUrl);

(9) Select CKFinder as preferred file browser in "Administer > Site configuration > CKEditor"
(in selected CKEditor profile scroll down to "File browser settings" section).

In the "File browser settings" section you may also change destination folders for files uploaded with CKFinder.

(10) Locate file named settings.php inside your drupal directory
drupal/sites/default/settings.php and on line 169 (# $cookie_domain = 'example.com';)
un-comment this line by removing # mark and change example.com to your domain name. Like this $cookie_domain = 'yourdomainname.com';

(Note: if you are on local computer add localhost $cookie_domain = 'localhost';).

(11) Open ckeditor>ckfinder>userfiles> and create three files named images, files and flash approximately.
(12) CKEditor Works only if you select Full HTML mode.

That`s it now put all these files in the sites>all>modules(note: you have to create this file.)

That`s it now go to administer and enable modules.
(note: Make sure that you have selected ckfinder as default file browser in ckeditor configuration. You can find this http://www.yoursitename.com/admin/settings/ckeditor here and then edit advanced user profile and set the ckfinder.

I hope I could help you. If anybody finds any difficulty to install or couldn`t understand what I explained here please contact me.

Checkout my site for more tutorials. How to install CKEditor and CKFinder!!!

Checkout my site for VIDEO tutorials. CKEditor and CKFinder Installation (Screen Cast) Video!!

I will be making a video tutorials about How to create your own custom CKEditor toolbar and plug-ins.

Default IP addresses, usernames & passwords of some routers and APs

Cisco LinkSys routers -

IP: 192.168.1.1
User name: (blank)
Password: admin

Cisco LinkSys APs -
IP: 192.168.1.245
User name: admin
Password: admin

Siemens router - SpeedStream 6520 -
IP: 192.168.254.254
User name: admin
Password: admin

Linksys WAP54G 
details: Wireless-G Access Point
Default IP address: 192.168.1.245 
Default admin username: <blank> 
Default admin password: admin 


=======

Linksys WRT300N Wireless-N Broadband Router
ip address: 192.168.1.1 username:(leave it blank)
password: admin

Linksys WRT150N Wireless-N Home Router
ip address: 192.168.1.1 username:(leave it blank)
password: admin

Linksys WRT330N Wireless-N Gigabit Gaming Router
ip address: 192.168.1.1 username:(leave it blank)
password: admin

Linksys WRT350N Wireless-N Gigabit Router with Storage Link
ip address: 192.168.1.1 username:(leave it blank)
password: admin
Linksys WRT600N Dual-Band Wireless-N Gigabit Router with Storage Link
ip address: 192.168.1.1 username:(leave it blank)
password: admin

Linksys WRVS4400N Wireless-N Gigabit Security Router with VPN
ip address: 192.168.1.1 username:(leave it blank)
password: admin

Linksys WRT100 RangePlus Wireless Router
ip address: 192.168.1.1 username:(leave it blank)
password: admin

Linksys WRH54G Wireless-G Home Router
ip address: 192.168.1.1 username:(leave it blank)
password: admin

Linksys WRT54G Wireless-G Broadband Router
ip address: 192.168.1.1 username:(leave it blank)
password: admin

Linksys WRT54G3G-AT Wireless-G Router for Mobile Broadband
ip address: 192.168.1.1 username:(leave it blank)
password: admin

Linksys WRT54G3G-ST Wireless-G Router for Mobile Broadband
ip address: 192.168.1.1 username:(leave it blank)
password: admin

Linksys WRT54GC Compact Wireless-G Broadband Router
ip address: 192.168.1.1 username:(leave it blank)
password: admin

Linksys WRT54GL Wireless-G Broadband Router ip address: 192.168.1.1 username:(leave it blank)
password: admin

Linksys WRT54GR Wireless-G Broadband Router with RangeBooster
ip address: 192.168.1.1 username:(leave it blank)
password: admin

Linksys WRT54GX2 Wireless-G Broadband Router with SRX200
ip address: 192.168.1.1 username:(leave it blank)
password: admin

Linksys WRT54GX4 Wireless-G Broadband Router with SRX400
ip address: 192.168.1.1 username:(leave it blank)
password: admin

Linksys WRTSL54GS Wireless-G Media Storage Link Router with SpeedBooster
ip address: 192.168.1.1 username:(leave it blank)
password: admin

Linksys WRV200 Wireless-G VPN Router with RangeBooster
ip address: 192.168.1.1 username:admin
password: admin

Linksys WRV54G Wireless-G VPN Broadband Router
ip address: 192.168.1.1 username:admin
password: admin

A Contact list does not show up in Outlook Address Book

Problem: When I want to send an email to people in a Contact list, I can not see the Contact list.

Solution: Right click on the Contact list, select 'Properties'. Click on 'Outlook Address Book'. Tick 'Show this folder as an e-mail Address Book'. Click on 'OK'.

How to set table borders as thin lines on a web page?

<table width="64%" cellpadding="5" style="border-collapse: collapse">
              <tr>
                <th width="46%" style="border-width: 1px; border-color: #000000; border-style: solid">Household Size</th>
                <th width="54%" style="border-width: 1px; border-color: #000000; border-style: solid">Household Income</th>
              </tr>
              <tr>
                <td style="border-width: 1px; border-color: #000000; border-style: solid">1 Person</td>
                <td style="border-width: 1px; border-color: #000000; border-style: solid">$22,229 </td>
              </tr>
</table>

What if VPN disconnects?

1. Open 'asdm-launcher.exe'.
2. Click on 'Configuration'.
3. Click on 'VPN'.
4.

How to show a specific Address Book firstly in Outlook?

1. Open Outlook.
2. 'Tools / Address Book'.
3. 'Tools / Options'.
4. Select one in 'Show this address list first'.
5. Click on 'OK'.
6. Done.

desktop turned 90 degrees

hit Ctrl+Alt and the up/down arrow keys it'll rotate the screen 90 degrees.

The application failed to initialize properly (0xc0000005):Google chrome

http://techblissonline.com/google-chrome-application-failed-initialize/

1. If you faced “The application failed to initialize properly (0xc0000005).Click on OK to terminate the application.” error with google chrome (chrome.exe) and you are using symantec, then you could try the following steps:


Back up the registry on an affected system
Open the registry on the Agent system by entering regedit from a run prompt
Navigate to HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\SysPlant
Open the Start DWORD
Change the value from 1 to 4 to disable the drivers
Reboot the system to commit the changes

2. The other easier solution is to run Google Chrome with --no-sandbox (with two dashes before “no”). To run it with the above option, edit the property of the shortcut you use to launch Google chrome and add the above option at the end of the “target” line (after the path to the chrome exe) i.e. Right click your shortcut to “Google Chrome” and click Properties. In the target text field, add a space then add --no-sandbox (with two dashes before “no”) right after the ending quotation mark. Run using this shortcut.However make sure that there is a space in between the ending quotation mark and the --no-sandbox option that you add.You could find a shortcut to google chrome on your desktop.Also note that you should use two dashes before “no”.

How to configure auto-forwarding for staff?

1. On Exchange Server, open 'Exchange Management Console'.
2. Under 'Recipient Configuration', click on 'Mail Contact'.
3. Right-click on it, and select 'New Mail Contact'. Add the other email address of the user.
4. Under 'Recipient Configuration', click on 'Mailbox'.
5. Select the user's mailbox.
6. Right-click on it, and select 'Properties'.
7. Select 'Mail Flow Settings'.
8. Select 'Delivery Options'.
9. Click on 'Properties'.
10. Click 'Add...'.
11. ...
12. Done.

Trust relationship failed

Symptom: Can not log in Windows domain, and see an error message saying 'Trust relationship failed.'
Resolution: Delete the domain connection from that machine. Log in with the local admin account. Re-connect to the domain.

Can not log in email accounts with Exchange Server

Symptom: Failed to log in, after entering username and password.
Solution: Go to Windows Domain Server. Remove the tick before 'User must change password'. Tick 'Password never expires'.

Copier - Cannon iR C3080 - print a report every time a fax is sent

On the admin web page, go to 'Add. Func. / Custom Settings / Report Settings / Fax Settings / Fax TX Report', change the value from 'For Error Only' into 'On'.

Microsoft Exchange Server Chinese Station

http://www.exchangecn.com/

How to link a flash to a website address?

Create another flash file (select ActionScript 2.0). Insert a new symbol - button. Import the former .swf file to the library. Click on the 'Up' frame. Drag the .swf animation from the library to the stage. Create key frames in all the 'Over', 'Down', 'Hit'. Exit symbel editing, and go to the flash file itself. Create an instance of the button on the stage. Click the button to select it. Open Window/Behaviours. Add a behaviour - 'Web / Go to Web Page'. Input the web address.

Done.

How to transfer Contacts to Exchange Server?

Copy them from 'Contacts in Personal Folders' into 'Contacts'.
Done.

How to transfer Calendars to Exchange Server?

1. Open Outlook.
2. Click 'View / Current View / All Appointments'.
3. Click 'Calendar in Personal folders'. Select all. Copy them.
4. Click 'Calendar'. Paste.
Done.

How to configure auto reply for staff?

Staff can do it by themselves.

Administrator can also do it for them. 1. log in 'https://webmail ...' with Administrator account.
2. Click on 'Options'.
3. At the top left corner, in 'Select what to manager', select 'Another User ...'.
4. Search for the person. Click on 'OK'.
5. Click on 'Tell people you're on vacation'.
6. ...

Connecting Finch Outlook to Midland Exchange Server

1. In the 'HOSTS' file, add '(IP address)      mailserver.csis3852.local'.
2. Log in with the employee's 3850 account.
3. Open 'Control Panel / Mail'.
4. Add a new email account, manually, not automatically.
5. For 'Server Name', enter 'mailserver.csis3852.local'.
6. For User Name, enter the employee's first name. Click on 'Check User Name' button.
7. For User Name, enter 'csis3852\(email user name)'. Enter the password.
8. Done.