Can not download a file in IE, but can download the same file in Chrome, etc.
Solution: change the extension name into .dat
24 November 2014
30 October 2014
Ubuntu Linux Network Configuration
https://help.ubuntu.com/10.04/serverguide/network-configuration.html
Ubuntu ships with a number of graphical utilities to configure your network devices. This document is geared toward server administrators and will focus on managing your network on the command line.
Ubuntu ships with a number of graphical utilities to configure your network devices. This document is geared toward server administrators and will focus on managing your network on the command line.
Ethernet interfaces are identified by the system using the naming convention of ethX, where X represents a numeric value. The first Ethernet interface is typically identified as eth0, the second as eth1, and all others should move up in numerical order.
To quickly identify all available Ethernet interfaces, you can use the ifconfig command as shown below.
ifconfig -a | grep eth
eth0 Link encap:Ethernet HWaddr 00:15:c5:4a:16:5a
sudo lshw -class network
*-network
description: Ethernet interface
product: BCM4401-B0 100Base-TX
vendor: Broadcom Corporation
physical id: 0
bus info: pci@0000:03:00.0
logical name: eth0
version: 02
serial: 00:15:c5:4a:16:5a
size: 10MB/s
capacity: 100MB/s
width: 32 bits
clock: 33MHz
capabilities: (snipped for brevity)
configuration: (snipped for brevity)
resources: irq:17 memory:ef9fe000-ef9fffff
Interface logical names are configured in the file
/etc/udev/rules.d/70-persistent-net.rules. If you would like control which interface receives a particular logical name, find the line matching the interfaces physical MAC address and modify the value of NAME=ethX to the desired logical name. Reboot the system to commit your changes. SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="00:15:c5:4a:16:5a", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth0"
SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="00:15:c5:4a:16:5b", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth1"
ethtool is a program that displays and changes Ethernet card settings such as auto-negotiation, port speed, duplex mode, and Wake-on-LAN. It is not installed by default, but is available for installation in the repositories.
The following is an example of how the interface identified as eth0 could be permanently configured with a port speed of 1000Mb/s running in full duplex mode.
sudo apt-get install ethtool
sudo ethtool eth0
Settings for eth0:
Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Advertised auto-negotiation: Yes
Speed: 1000Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 1
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: g
Wake-on: d
Current message level: 0x000000ff (255)
Link detected: yes
/etc/network/interfaces. The following is an example of how the interface identified as eth0 could be permanently configured with a port speed of 1000Mb/s running in full duplex mode.
auto eth0 iface eth0 inet static pre-up /usr/sbin/ethtool -s eth0 speed 1000 duplex full
![[Note]](https://help.ubuntu.com/libs/admon/note.png) | |
| Although the example above shows the interface configured to use the static method, it actually works with other methods as well, such as DHCP. The example is meant to demonstrate only proper placement of the pre-up statement in relation to the rest of the interface configuration. |
The following section describes the process of configuring your systems IP address and default gateway needed for communicating on a local area network and the Internet.
For temporary network configurations, you can use standard commands such as ip, ifconfig and route, which are also found on most other GNU/Linux operating systems. These commands allow you to configure settings which take effect immediately, however they are not persistent and will be lost after a reboot.
To temporarily configure an IP address, you can use the ifconfig command in the following manner. Just modify the IP address and subnet mask to match your network requirements.
To temporarily configure an IP address, you can use the ifconfig command in the following manner. Just modify the IP address and subnet mask to match your network requirements.
sudo ifconfig eth0 10.0.0.100 netmask 255.255.255.0
ifconfig eth0
eth0 Link encap:Ethernet HWaddr 00:15:c5:4a:16:5a
inet addr:10.0.0.100 Bcast:10.0.0.255 Mask:255.255.255.0
inet6 addr: fe80::215:c5ff:fe4a:165a/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:466475604 errors:0 dropped:0 overruns:0 frame:0
TX packets:403172654 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:2574778386 (2.5 GB) TX bytes:1618367329 (1.6 GB)
Interrupt:16
sudo route add default gw 10.0.0.1 eth0
route -n
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
10.0.0.0 0.0.0.0 255.255.255.0 U 1 0 0 eth0
0.0.0.0 10.0.0.1 0.0.0.0 UG 0 0 0 eth0
/etc/resolv.conf. The example below shows how to enter two DNS servers to /etc/resolv.conf, which should be changed to servers appropriate for your network. A more lengthy description of DNS client configuration is in a following section. nameserver 8.8.8.8 nameserver 8.8.4.4If you no longer need this configuration and wish to purge all IP configuration from an interface, you can use the ip command with the flush option as shown below.
ip addr flush eth0
| | |
Flushing the IP configuration using the ip command does not clear the contents of /etc/resolv.conf. You must remove or modify those entries manually. |
To configure your server to use DHCP for dynamic address assignment, add the dhcp method to the inet address family statement for the appropriate interface in the file
/etc/network/interfaces. The example below assumes you are configuring your first Ethernet interface identified as eth0. auto eth0 iface eth0 inet dhcpBy adding an interface configuration as shown above, you can manually enable the interface through the ifup command which initiates the DHCP process via dhclient.
sudo ifup eth0
sudo ifdown eth0
To configure your system to use a static IP address assignment, add the static method to the inet address family statement for the appropriate interface in the file
/etc/network/interfaces. The example below assumes you are configuring your first Ethernet interface identified as eth0. Change the address, netmask, and gateway values to meet the requirements of your network. auto eth0 iface eth0 inet static address 10.0.0.100 netmask 255.255.255.0 gateway 10.0.0.1By adding an interface configuration as shown above, you can manually enable the interface through the ifup command.
sudo ifup eth0
sudo ifdown eth0
The loopback interface is identified by the system as lo and has a default IP address of 127.0.0.1. It can be viewed using the ifconfig command.
ifconfig lo
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:2718 errors:0 dropped:0 overruns:0 frame:0
TX packets:2718 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:183308 (183.3 KB) TX bytes:183308 (183.3 KB)
/etc/network/interfaces responsible for automatically configuring your loopback interface. It is recommended that you keep the default settings unless you have a specific purpose for changing them. An example of the two default lines are shown below. auto lo iface lo inet loopback
Name resolution as it relates to IP networking is the process of mapping IP addresses to hostnames, making it easier to identify resources on a network. The following section will explain how to properly configure your system for name resolution using DNS and static hostname records.
To configure your system to use DNS for name resolution, add the IP addresses of the DNS servers that are appropriate for your network in the file
Below is an example of a typical configuration of
If you have multiple domains you wish to search, your configuration might look like the following.
If no matches are found, the DNS server will provide a result of notfound and the DNS query will fail.
/etc/resolv.conf. You can also add an optional DNS suffix search-lists to match your network domain names. Below is an example of a typical configuration of
/etc/resolv.conf for a server on the domain "example.com" and using two public DNS servers. search example.com nameserver 8.8.8.8 nameserver 8.8.4.4The search option can also be used with multiple domain names so that DNS queries will be appended in the order in which they are entered. For example, your network may have multiple sub-domains to search; a parent domain of example.com, and two sub-domains, sales.example.com and dev.example.com.
If you have multiple domains you wish to search, your configuration might look like the following.
search example.com sales.example.com dev.example.com nameserver 8.8.8.8 nameserver 8.8.4.4If you try to ping a host with the name of server1, your system will automatically query DNS for its Fully Qualified Domain Name (FQDN) in the following order:
- server1.example.com
- server1.sales.example.com
- server1.dev.example.com
Static hostnames are locally defined hostname-to-IP mappings located in the file
The following is an example of a
/etc/hosts. Entries in the hosts file will have precedence over DNS by default. This means that if your system tries to resolve a hostname and it matches an entry in /etc/hosts, it will not attempt to look up the record in DNS. In some configurations, especially when Internet access is not required, servers that communicate with a limited number of resources can be conveniently set to use static hostnames instead of DNS. The following is an example of a
hosts file where a number of local servers have been identified by simple hostnames, aliases and their equivalent Fully Qualified Domain Names (FQDN's). 127.0.0.1 localhost 127.0.1.1 ubuntu-server 10.0.0.11 server1.example.com server1 vpn 10.0.0.12 server2.example.com server2 mail 10.0.0.13 server3.example.com server3 www 10.0.0.14 server4.example.com server4 file
| | |
| In the above example, notice that each of the servers have been given aliases in addition to their proper names and FQDN's. Server1 has been mapped to the name vpn, server2 is referred to as mail, server3 as www, and server4 as file. |
The order in which your system selects a method of resolving hostnames to IP addresses is controlled by the Name Service Switch (NSS) configuration file
To modify the order of the above mentioned name resolution methods, you can simply change the hosts: string to the value of your choosing. For example, if you prefer to use legacy Unicast DNS versus Multicast DNS, you can change the string in
/etc/nsswitch.conf. As mentioned in the previous section, typically static hostnames defined in the systems /etc/hosts file have precedence over names resolved from DNS. The following is an example of the line responsible for this order of hostname lookups in the file /etc/nsswitch.conf. hosts: files mdns4_minimal [NOTFOUND=return] dns mdns4
- files first tries to resolve static hostnames located in
/etc/hosts. - mdns4_minimal attempts to resolve the name using Multicast DNS.
- [NOTFOUND=return] means that any response of notfound by the preceeding mdns4_minimal process should be treated as authoritative and that the system should not try to continue hunting for an answer.
- dns represents a legacy unicast DNS query.
- mdns4 represents a Multicast DNS query.
/etc/nsswitch.conf as shown below. hosts: files dns [NOTFOUND=return] mdns4_minimal mdns4
Bridging multiple interfaces is a more advanced configuration, but is very useful in multiple scenarios. One scenario is setting up a bridge with multiple network interfaces, then using a firewall to filter traffic between two network segments. Another scenario is using bridge on a system with one interface to allow virtual machines direct access to the outside network. The following example covers the latter scenario.
Before configuring a bridge you will need to install the bridge-utils package. To install the package, in a terminal enter:
Now restart networking to enable the bridge interface:
Before configuring a bridge you will need to install the bridge-utils package. To install the package, in a terminal enter:
sudo apt-get install bridge-utils
Next, configure the bridge by editing /etc/network/interfaces: auto lo
iface lo inet loopback
auto br0
iface br0 inet static
address 192.168.0.10
network 192.168.0.0
netmask 255.255.255.0
broadcast 192.168.0.255
gateway 192.168.0.1
bridge_ports eth0
bridge_fd 9
bridge_hello 2
bridge_maxage 12
bridge_stp off
| | |
| Enter the appropriate values for your physical interface and network. |
sudo /etc/init.d/networking restart
The new bridge interface should now be up and running. The brctl provides useful information about the state of the bridge, controls which interfaces are part of the bridge, etc. See man brctl for more information. - The Ubuntu Wiki Network page has links to articles covering more advanced network configuration.
- The interfaces man page has details on more options for
/etc/network/interfaces. - The dhclient man page has details on more options for configuring DHCP client settings.
- For more information on DNS client configuration see the resolver man page. Also, Chapter 6 of O'Reilly's Linux Network Administrator's Guide is a good source of resolver and name service configuration information.
- For more information on bridging see the brctl man page and the Linux Foundation's Net:Bridge page.
Ubuntu Linux - How to install software?
https://help.ubuntu.com/12.04/serverguide/installing-from-cd.html
Installing the package groups is accomplished using the tasksel utility. One of the important differences between Ubuntu (or Debian) and other GNU/Linux distribution is that, when installed, a package is also configured to reasonable defaults, eventually prompting you for additional required information. Likewise, when installing a task, the packages are not only installed, but also configured to provided a fully integrated service.
Installing the package groups is accomplished using the tasksel utility. One of the important differences between Ubuntu (or Debian) and other GNU/Linux distribution is that, when installed, a package is also configured to reasonable defaults, eventually prompting you for additional required information. Likewise, when installing a task, the packages are not only installed, but also configured to provided a fully integrated service.
Once the installation process has finished you can view a list of available tasks by entering the following from a terminal prompt:
tasksel --list-tasks
The output will list tasks from other Ubuntu based distributions such as Kubuntu and Edubuntu. Note that you can also invoke the tasksel command by itself, which will bring up a menu of the different tasks available.
You can view a list of which packages are installed with each task using the --task-packages option. For example, to list the packages installed with the DNS Server task enter the following:
tasksel --task-packages dns-server
The output of the command should list:
bind9-doc bind9utils bind9
If you did not install one of the tasks during the installation process, but for example you decide to make your new LAMP server a DNS server as well, simply insert the installation CD and from a terminal:
sudo tasksel install dns-server
22 October 2014
Can Not Log On
`you cannot logon because the logon method you are using is not allowed on this computer windows 7'
Solution:
https://social.technet.microsoft.com/Forums/windows/en-US/0f750de8-d56e-4951-a2b1-839e55934745/non-admin-users-cannot-logon-to-the-domain-on-windows-7-wks?forum=w7itpronetworking
Symptom: When trying to logon a computer using non administrator ID, you may receive this message: "You cannot log on because the logon method you are using is not allowed on this computer. Please see you network administrator for more details."
Case 1: Group Policy' "Allow log on locally" was not setup to allow users or domain users. To setup allow users or domain users to logon the computer or domain, you need to add the users or domain users to the "Allow log on locally". Please follow these steps to add the users.
1. Run gpedit.msc.
2. Expand Windows Settings\Security Settings\Local Policies
3. Click on User Rights Assignment
4. Ensure that "Allow log on locally" includes Administrators, Backup
Operators, Domain Users or Users.
Case 2: Group Policy' "Deny log on locally" was setup to deny users or domain users. To setup allow users or domain users to logon the computer or domain locally, "Deny log on locally" should be empty or no users or domain users in the list. Please follow these steps to remove the users or domain users from the "Deny log on locally".
1. Run gpedit.msc.
2. Expand Windows Settings\Security Settings\Local Policies
3. Click on User Rights Assignment
4. Ensure that "Deny log on locally" is empty.
Case 3: The local group policy allow user to logon. However, domain group policy which overrides local policy doesn't allow users to logon locally. The resolution is modify the domain policy to allow users to logon locally.
Case 4: The domain policy allows domain users to logon locally, but the local policy doesn't and the domain policy doesn't apply to the computer. The fix is running gpupdate to force to update the domain policy.
Case 5: Norton Firewall blocks the communication between the client and domain controller. The solution is disabling Norton firewall or re-configuring it to allow to access the domain controller.
MCSE, MCSA, MCDST [If this post helps to resolve your issue, please click the "Mark as Answer" or "Helpful" button at the top of this message. By marking a post as Answered, or Helpful you help others find the answer faster.]
Solution:
https://social.technet.microsoft.com/Forums/windows/en-US/0f750de8-d56e-4951-a2b1-839e55934745/non-admin-users-cannot-logon-to-the-domain-on-windows-7-wks?forum=w7itpronetworking
Symptom: When trying to logon a computer using non administrator ID, you may receive this message: "You cannot log on because the logon method you are using is not allowed on this computer. Please see you network administrator for more details."
Case 1: Group Policy' "Allow log on locally" was not setup to allow users or domain users. To setup allow users or domain users to logon the computer or domain, you need to add the users or domain users to the "Allow log on locally". Please follow these steps to add the users.
1. Run gpedit.msc.
2. Expand Windows Settings\Security Settings\Local Policies
3. Click on User Rights Assignment
4. Ensure that "Allow log on locally" includes Administrators, Backup
Operators, Domain Users or Users.
Case 2: Group Policy' "Deny log on locally" was setup to deny users or domain users. To setup allow users or domain users to logon the computer or domain locally, "Deny log on locally" should be empty or no users or domain users in the list. Please follow these steps to remove the users or domain users from the "Deny log on locally".
1. Run gpedit.msc.
2. Expand Windows Settings\Security Settings\Local Policies
3. Click on User Rights Assignment
4. Ensure that "Deny log on locally" is empty.
Case 3: The local group policy allow user to logon. However, domain group policy which overrides local policy doesn't allow users to logon locally. The resolution is modify the domain policy to allow users to logon locally.
Case 4: The domain policy allows domain users to logon locally, but the local policy doesn't and the domain policy doesn't apply to the computer. The fix is running gpupdate to force to update the domain policy.
Case 5: Norton Firewall blocks the communication between the client and domain controller. The solution is disabling Norton firewall or re-configuring it to allow to access the domain controller.
MCSE, MCSA, MCDST [If this post helps to resolve your issue, please click the "Mark as Answer" or "Helpful" button at the top of this message. By marking a post as Answered, or Helpful you help others find the answer faster.]
20 October 2014
how to synchronize time in windows 7
http://technet.microsoft.com/en-us/library/cc758905(WS.10).aspx
Administrative Credentials
To perform this procedure, you must be a member of the Administrators group on the local computer. To perform this procedure from a remote computer, you must be a member of the Domain Admins group.
Administrative Credentials
To perform this procedure, you must be a member of the Administrators group on the local computer. To perform this procedure from a remote computer, you must be a member of the Domain Admins group.
To configure a client computer for automatic domain time synchronization
- Open a Command Prompt.
- Type the following command and then press ENTER:
w32tm /config /syncfromflags:domhier /update - Type the following command and then press ENTER:
net stop w32time - Type the following command and then press ENTER:
net start w32time
07 October 2014
How to change colour in Illustrator CS5?
Select the layer. Select the object.
Edit | Edit Colour | Re-colour artwork.
Enter the 3 numbers for H, S, B. OK.
Save it as .ai. Save it as .eps.
Edit | Edit Colour | Re-colour artwork.
Enter the 3 numbers for H, S, B. OK.
Save it as .ai. Save it as .eps.
Subscribe to:
Posts (Atom)